RoHS material control Vietnam country-of-origin documentation rfq@saolamfg.comEmail WhatsApp +84 86 501 7914

Guide

What are buttress thread dimensions, and how do you call a buttress thread on a drawing?

Short answer

A buttress thread is an asymmetric screw thread with one nearly square flank that takes the load and one steep flank that only clears, made for parts that carry high thrust in one direction along the axis. Short answer: the American inch form in ASME B1.9 has a 7° pressure flank, a 45° clearance flank and a basic height of thread engagement of 0.6 times the pitch; on the drawing you must give diameter, threads per inch, which flank leads (push or pull), the form and the class, because the form only works when the 7° flank faces the load.

By Saola Manufacturing engineering team · Published · Updated

Symmetric power threads for lead screws are compared in ACME or metric trapezoidal thread, and the lathe process that usually cuts large special threads in single point threading. This page covers the buttress form itself: its dimensions, its callout and how it is accepted.

On this page

What does the buttress thread form look like?

The load side of the tooth is almost perpendicular to the axis and the back side is sloped at 45°, so it carries heavy thrust in one direction with little radial push on the mating part.

The National Bureau of Standards screw-thread handbook defines the basic form with a pressure flank angle, measured in an axial plane, of 7° from the normal to the axis, a clearance flank angle of 45°, equal crest truncations on the internal and external threads so that the basic depth of engagement is 0.6p, and equal root radii tangent to both flanks (NBS Handbook H28 (1957), Part III, section XIV, issued 1960). The pressure flank is the one that takes the thrust in the assembly; the clearance flank does not.

The same handbook explains the choice of 7°: a survey of wartime practice found pressure flank angles from 0 to more than 15° and clearance flank angles from 30 to 55°, and the committee picked 7° because it closely approaches the static angle of friction for well-lubricated steel surfaces. Because the thrust side is nearly perpendicular to the axis, the radial component of the thrust is small, which is why the form suits tubular members screwed together; the handbook names breech mechanisms of large guns and airplane propeller hubs as examples.

What are the basic dimensions of a 7/45 buttress thread?

Every basic dimension is a fixed multiple of the pitch, so once you know the threads per inch you can derive the height, truncations and root radius; the limits then come from the class tables.

Per NBS Handbook H28 Part III, which states it is in substantial agreement with ASA B1.9, the 7/45 form has these basic relationships, where p is the pitch: height of the sharp-V thread 0.89064p, basic height of thread engagement 0.6p, root radius 0.07141p, root truncation 0.08261p, crest truncation 0.14532p, and thread height of both internal and external thread 0.66271p (NBS Handbook H28, 1960). The handbook adds that on thin-walled tubing the minimum root truncation may be used with a larger maximum, so a thin-wall part should say so.

The handbook recommends selecting nominal diameters from a preferred geometric series and pitches from a preferred series of 20, 16, 12, 10, 8, 6, 5, 4, 3, 2-1/2, 2, 1-1/2, 1-1/4 and 1 threads per inch, with associated pitches growing coarser as the diameter grows. The current standard, ASME B1.9-1973, is still active and reaffirmed, and its scope covers the 7/45 form with 0.6p basic height, a table of preferred diameter-pitch combinations, a pitch diameter tolerance formula, tolerances on major and minor diameters, a system of allowances, methods of measuring and gaging, and dimensional acceptability of product (ASME B1.9-1973 (R2025)). ASME has placed it on stabilized maintenance, so it is not routinely revised. Use the paid standard for the limit tables; the factors above are the basic form.

Basic 7/45 buttress thread relationships (p = pitch) · source: NBS Handbook H28 (1957) Part III, section XIV, issued 1960, in substantial agreement with ASA B1.9; current inch standard ASME B1.9-1973 (R2025)
ElementBasic valueWhy it matters on the drawing
Pressure (load) flank angle7° from the normal to the axisMust face the load; leading flank must be stated
Clearance flank angle45°Has more effect on pitch diameter measurement
Height of sharp-V thread0.89064pReference for the tool form
Basic height of engagement0.6pDistinguishes the American form from the 0.4p British form
Thread height, internal and external0.66271pSets tool depth and minor diameters
Root radius0.07141pRoot strength; note thin-wall exceptions
Crest truncation0.14532pCrest flat width on both members

Which buttress forms exist besides the ASME 7/45 thread?

Several, and they do not interchange: the British 0.4p form, the German metric buttress series in DIN 513, and oilfield buttress casing threads under API Spec 5B. The drawing has to name which one.

NBS Handbook H28 describes the British Standard buttress thread of BS 1657:1950 as having a basic depth of thread of 0.4p instead of the 0.6p of the American form, and records that the two countries agreed to include each other's essential details in appendixes, with ASA B1.9-1953 issued in conformance with that recommendation (NBS Handbook H28, 1960). Metric buttress threads are standardized in Germany as DIN 513; Part 1, Thread profiles, is current in its 2020 edition (DIN 513-1:2020-12, DIN). Take its profile and pitches from that standard; do not assume they match the inch form.

Buttress casing threads on oil country pipe are a separate system: API Specification 5B covers threading, gauging and inspection of casing, tubing and line pipe threads, and its 17th edition, announced in 2026, updated the dimensions and tolerances of buttress tooth thickness gauges (American Petroleum Institute, 2026). The same announcement says mechanical gauging governs acceptance when results from other measurement methods are disputed; casing threads are a separate system from a machined buttress screw on a press or a clamp.

How do you write a buttress thread callout on a drawing?

Give the basic major diameter, threads per inch (or pitch and lead for multiple starts), whether the internal member pushes or pulls, the form abbreviation, the class and LH if left-hand, and name the standard and edition in a note.

NBS Handbook H28 sets out the designation as nominal major diameter, threads per inch, the symbol showing whether the screw is to push or pull, the abbreviation N BUTT, then the class number; LH is added for a left-hand thread and nothing for right-hand; for a multiple-start thread the pitch and lead are given instead of threads per inch. It defines three classes, 1 (free), 2 (medium) and 3 (close), and works through a 2.080-4 class 2 example (NBS Handbook H28, 1960). The handbook format is historical; check the designation format in the edition of ASME B1.9 named on your drawing.

The push or pull symbol is the part most often missed. The handbook says it is important when ordering product, tools or gages to state whether the 7° pressure flank or the 45° clearance flank is the leading flank: if the screw is designed to push, the pressure flank leads on both screw and nut; if it pulls, the clearance flank leads. Without it, the supplier has to guess which way the thread is cut. A safe practice is a small section view of the thread showing which way the load acts, in addition to the callout.

For the RFQ, list the thread callout, the standard and edition, the length of full thread, any thin-wall note, the material and heat-treat condition, and who supplies the gauges.

How are buttress threads gauged and accepted?

With go and not-go thread gauges made to the buttress form, plain gauges for the minor and major diameters, and checks of lead and flank angle; standard UN thread gauges do not apply, so the gauges have to be planned with the part.

For external threads the handbook recommends go and not-go snap or ring gages for major diameter, a go thread ring gage at maximum pitch diameter, a not-go thread ring or snap gage at minimum pitch diameter, measurement of pitch over the whole length of engagement, and measurement of both flank angles by optical projection or templates. Internal threads get go and not-go thread plug gages, plain plug gages for the minor diameter, and flank angles checked by optical projection from casts (NBS Handbook H28, 1960).

The handbook also warns that measuring pitch diameter is harder than on a symmetric thread, because the 45° clearance flank has a greater effect on the reading than the 7° flank, so best-size wires and a tightly held clearance flank angle are needed on gages. A pitch error has a large effect: per NBS Handbook H28, a pitch deviation δp changes the virtual pitch diameter by 2δp divided by (tan 45° + tan 7°), about 1.78 times the pitch deviation. In practice, agree before the order whether the supplier buys thread gauges, the buyer lends master gauges, or acceptance is by a measured method listed on the first-article report.

How are buttress threads made on turned parts?

Usually by single point threading on a CNC lathe with a ground form tool or insert for the exact pitch and hand of the flank, or by thread milling or grinding; taps and dies for buttress forms are special tools.

The handbook notes that the standard form was chosen with manufacture by thread milling or grinding in mind, and that since buttress threads are used mainly on specially designed components, the handbook gave only suggested diameter-pitch pairings rather than a fixed series; the current ASME B1.9 scope does include a table of preferred diameter-pitch combinations, but special pitches remain common as general practice. Because the tool profile is asymmetric, the same insert cannot cut a push and a pull thread on the same side of the part, and the tool must match the threads per inch, so as general practice the tooling is planned per part number. A buttress thread on a long, slender part also needs support while it is cut, and as with other large threads the finish and form depend on the material and set-up.

As general practice, if the thread is heat treated after machining, state on the drawing whether the gauges apply before or after heat treatment.

Can Saola machine a buttress thread on your part?

Turning runs at our lead CNC plant on conventional CNC lathes for small bar and tube parts, as the turning page describes; a buttress form, its class and its gauging are confirmed at drawing review before we quote.

The CNC turning page lists the bar materials and notes that threads are checked with go/no-go gauges; a buttress thread needs gauges made for that form, so we agree at drawing review who provides them or how the thread is measured instead. Inspection equipment at the plant includes a 2D optical (vision) measuring instrument and a height gauge. First-article inspection reports for new parts and a dimensional inspection record per lot are available on request, and the thread can be listed as a characteristic on both. Send the drawing with the thread callout and load direction through the quote form.

Frequently asked

Why is a buttress thread called a buttress thread?

Because one flank stands nearly upright like a wall and the other slopes away behind it, like a buttress supporting a wall against force from one side. The shape only carries high load in one axial direction.

Can a buttress thread take load in both directions?

It carries load best in one direction, on the 7° pressure flank. The form is designed so that thrust on the near-perpendicular flank has a small radial component, which is why the push or pull direction must be on the drawing. For loads in both directions a symmetric thread such as ACME or metric trapezoidal is the usual choice.

Is the 45/7 buttress the same as a DIN 513 metric buttress thread?

Treat them as different standards: DIN 513 is a metric series and ASME B1.9 an inch series, so do not expect parts made to one to mate with the other. Name the standard on the drawing.

What do the classes 1, 2 and 3 mean on a buttress thread?

Per NBS Handbook H28, class 1 is free, class 2 medium and class 3 close; class 2 is the basis of the pitch diameter tolerance formula and the other classes are scaled from it. Pick the class from the fit your assembly needs, not by habit.

Where can I get buttress thread limit tables?

From the current ASME B1.9 for the inch form, DIN 513 for the metric form, or API Spec 5B for casing threads. The older NBS Handbook H28 is open but historical; check its values against the edition your drawing calls.

Have a drawing for this? Send it for a quote.

STEP or PDF, one part or a whole family. You get a unit price at your volume, the tooling cost, and a short manufacturability note.